How to Repair Bifold Door Top Roller Guide

If your bifold door is squeaking then it's likely that they need some maintenance. They might require cleaning, lubricated or adjusted. The problem may be caused by an unfastened screw on the top pivot or the top guide roller.

This kit includes all the necessary hardware to restore your bi-fold door repair closet door system to its best performance.

Take the door off

It may seem complicated and difficult to install a set of bifold internal doors but for DIYers with some experience it's actually a breeze. Getting the frame into position isn't a major issue; the tricky part is getting the doors to fold and close easily and accurately. Because repair bifold door top roller doors are intricate machines, they might require some tuning to keep functioning properly. It could be as easy as tightening a screw, or as complicated as removing and replacing the door's pivot pin or roller.

Most of the time you can resolve these issues with a few simple adjustments, without having to remove the doors. You might notice that your bifold doors are sliding and scraping the floor or slipping off track. The solution to these issues isn't difficult, and with three easy steps your bifold doors can be back in short time.

The most common problem that bifolding doors with internal hinges face is that they slide out of alignment. This can be caused by loose screws, holes in the anchor pins, or simply a door that is not aligned. Most of the time this can be fixed by a few simple adjustments. If, however, your door doesn't move in any way, you might have to replace it.

To remove the door, you'll need an appropriate screwdriver, and possibly a pair of pliers (to assist in loosening any tight pivot pins). The screwdriver can be used to break any locking levers on the bottom pivot bracket and the pliers allow you to pull the pin and take it off.

After the top roller is removed Once the top roller is removed, you can raise the door, turn it down and then remove it from its track and pivot brackets. This is usually quite straightforward however, be sure not to let the door hit against the door frame. You should then be able to saw off the edge of the door that's scraping the floor and sand it down until smooth. You can then paint or refinish the door as necessary.

Remove the Roller Guide

This spring-loaded guide roller is mounted on the top edge of the bifold door to assist with smooth operation. It is designed for Kenna frames, and can fit door panels that range from 1 inch to 1-3/8 inches thick. It is made of nylon, steel and plastic components and can replace a damaged or worn-out guide.

Remove any screws holding the guide to the roller using a screwdriver. Then, use your hands to lift it out of the frame. This may require some effort, so let a friend help you to keep the door in place while you remove it.

Once the guide you used to guide your child is removed, carefully cut through the remaining finish around the foot of the new guide using a razor blade to remove it from the rod blank. This will make it easier to remove and will prevent damage to the new guide foot. The guide foot is extremely sharp and could cut or nick fingers.

It is likely that you will need to use some force to take the guide off, but be careful not to chip or break the foot. After you have removed the guide from the rod blank, make sure to get rid of all the threads and epoxy remaining in the area where it was affixed. This will help prevent any future problems with the guide.

After you have removed the guide, you can test your new guide by putting it in its place and then applying a few turns of masking tape or some form of guide tubing to secure it in place. This allows you to double check the alignment of your guide and spacing to ensure everything is set up correctly. If you're eyeballing it or using the always accurate CRB Spine Finder and Deflection System it is essential to prevent any issues in the future.

If the guide is placed correctly and functioning as it should then the final step is to put the door back in place. Remember to replace and tighten any screws or pins that you removed or loosen.

Take the Bottom Pivot off.

Bifold doors can be a stunning addition to any home, but they may require to be tweaked or adjusted to ensure they remain in good shape. While some of the less critical issues can be resolved with the doors still in place, other issues will require removal. This guide will walk you through the process of removing internal bifold door pivots, pins and rollers to make your doors glide like new.

The first step is to gather your tools. Putting everything together prior to time will help you avoid a lot of frustration later in the process. You'll also require an plier and a screwdriver. A basic set of tools is available at a reasonable cost at your local hardware store. It's important to keep some wood glue on hand. This will be useful if you need to put the rollers in their place.

After gathering your tools then open the bifold doors and loosen the top track bracket by using your screwdriver. Once the bracket is in place, you should be able to lift the door off of the top track. It might take a little dancing but it should eventually pop off the track.

The pivot on the bottom of the frame needs to be removed. Close all interior doors prior to starting. This will make it much simpler instead of working from the inside. If the bottom track still appears to be in good condition, you can simply lift the door and take off the track.

If the track is damaged, then you'll need to replace it. Hardware stores sell replacement tracks for bifold doors as well as swinging closet doors. If the track is severely damaged, then you might need to replace it completely.

You'll now need to check your doors for their proper operation. Check that the doors can move in and out of their positions effortlessly. You'll want to ensure that the edges of your bi-fold door repairs near me are aligned with the frame when it is closed. If they aren't, then you'll need to readjust the top pivot bracket and tighten or loosen the bottom set screw until the door's edge is perfectly aligned with the frame.

Replace the Roller

If they are installed properly they can be used to enclose pantries, laundry nooks and closets. They comprise two door panels that are hinged and open up on a track that sits in the frame's top. Over time, the roller guides can wear out and cause the doors to slide. The roller guide can be replaced in just a few minutes using a few tools.

The first step is to take the guide for the roller from the door panel. This involves removing the bottom pivot bolt and loosening the screw that holds the guide at its top. Once the guide is removed and the door panel is lifted up and away from its track. Then with a wrench, remove the top pivot bolt from the hole in the header of the frame by loosening the nut.

Stanley, Cox and Acme offer a top nylon replacement roller that has a 7/8-inch diameter wheel that rests on a steel base. It mounts at the top of bifold doors that range from 1 to 1-3/8 inches thick. It comes spring-loaded and adjusts itself in the upper track to ensure smooth glide.

Another common problem with bifold doors is that it scrapes the floor when it closes or opens. This is often the result of adding carpet or other flooring materials which require the doors be raised slightly to allow for clearance. This issue can be solved by taking off the screws that adjust the bottom pivot and loosening the top track mounting screws and moving the anchor/pivot.

A set top roller with new guides can be an inexpensive solution to the problem of your bifold doors becoming difficult to operate. They are usually available at your local hardware store in the door section, but they're also accessible online from a number of suppliers. You'll also require an elongated squeeze-clamp as well as a small container Elmer's wood adhesive, which can be found in big box stores. The clamp is used to keep the repair bifold door bottom pivot area in place after the glue has been inserted and allowed to dry.