Patio Door Lock Repairs

Over time, glass patio door repair doors experience wear and tear that can result in lock malfunctions. There are a few basic steps you can take to restore the security of your uPVC door.

These quick fixes will make your home safer regardless of whether you re-align the lock or clean the locking mechanism.

Clean the Lock

Although patio doors are a great way to let the outside in and keep the elements out however, they can also pose a security risk if your lock isn't working as it should. Over time, wear and tear, cold and hot weather, dirt, and debris can cause your patio door lock to become difficult to operate. With a little care you can ensure that your patio doors repair near me door's locks will always perform correctly.

It's crucial to clean the lock of your patio door and all its moving parts. This will help get rid of any dirt or coatings that might be hindering your lock from functioning effectively. Begin by wiping down all the moving parts of the lock for your patio door with an aqueous cloth. Then apply a scouring pad or rough damp cloth to scrub the areas that are soiled of the door frame and frame. Then clean the lock with a dry cloth to get rid of any remaining moisture. Let it air dry before you use it.

If you have an exterior door that is fitted with a pin tumbler latch mechanism You can apply lubrication to the lock by applying powdered graphite to the key or by using a Teflon-based lubricant like WD-40 Multi-Use. This type of lubricant can be applied quickly and will not disintegrate over time. If you're unable to locate the right lubricant for your needs you can try using a pencil with an extremely thick tip. Insert the pencil into the lock and jiggle it around to distribute the graphite.

Regular maintenance is also necessary to keep the tracks of sliding patio door glass repair doors free from dirt, dust and debris. They are particularly susceptible to snow and ice which can cause them to become stuck or slack and make it difficult for your patio doors to open and close.

Sliding patio door track rails and rollers can be cleaned by removing dirty or damaged weather stripping and then cleaning it, before reinstalling it. The rollers of patio doors can be cleaned and sprayed down with an oil that is non-stick.

Lubricate the moving parts

uPVC french doors, similar to sliding patio doors, operate with 3-4 or sometimes 5-point locking mechanisms that include the handle and lock cylinder controlled by the key. These doors also need maintenance, including lubrication of the moving parts. This can be done with a thin oil (never WD40) and should be done once per year.

If sagging hinges don't cause the issue it could be because the door is not aligned. It could be rubbing or catching against the strike plate's hole in the frame. The solution is to take off the strike plate, and then use an abrasive chisel to increase the size of the mortise it sits in. This will allow the latch to fit properly into the hole and prevent it from rubbing against the frame.

Take a measurement of the width of the cylinder with the help of a piece of book or wood that can be inserted into the gap above the adjustment screw. The outer dimension is measured from the outside of the door to the center cylinder. The inner dimension is measured from the center adjustment screw to the end of the cylinder.

Check the width of the lock.

If your patio door latch is difficult to turn even after cleaning and oiling it could be because it is not aligned with the strike plate. Check to see if the door is balanced and whether the hinge screws are secure However, in many cases it is possible to move the strike plate up or down could fix the problem.

The latch may not be able to engage properly if the strike of the lock is not large enough. In this case, enlarge the hole with an hammer and chisel. Then, test the latch to ensure that it does not rub against the jamb frame of the door or get caught on it.

Before you purchase a replacement lock, first determine the mortise type of lock you have. This can be done by looking at the end faceplate and observing whether it is round or square. Then, take a look at the screw holes on the current lock and note the dimensions of each one. This information will aid you in finding an alternative that is of the same size and will fit perfectly into the hole you have already.

You'll need to identify the mortise lock, and then examine it for any scratches, bends or other damage that need to be repaired. A badly bent or damaged latch is more likely than one that has been used a lot to break. Replace the lock if you notice evidence of damage.

After you've determined the type of lock replacement that you require It's time to start the actual repair. The old handle and spindle must be removed from the doorway to the patio sliding doors repair. Introduce the new handle. Start by installing the inside handle. Align it with the spindle, and then secure it in place using the two screws or bolts. Once the handle in the interior is installed, you can install the exterior handle and screw it in place as well. After you've completed these steps, test the handles to ensure that they open and shut easily and that the latch engages correctly with the strikeplate.

Check the Strike of the Door.

The strike plate and the door latch are two pieces which work together to secure the door. If they are not aligned properly, the latch won't latch the door properly. This problem is usually very easy to fix.

First, examine the strike plate's receiving holes to make sure they are free of obstructions, such as dirt or plastic plugs. Then loosen the keeper screws that hold the strike plate in place and allow it to move vertically, but not removing it from the frame of your door. Adjust the strike plate so that it aligns its holes for receiving with latch hooks of the door latch. After the strike plate is adjusted then tighten all screws, and test if the door closes smoothly.

These plates are difficult to reach for homeowners with Sliding patio door repair service near me patio doors. However they are vital to lock and unlock your door. These metal plates are located between the top and bottom jambs of your door, where they serve as the support for the latch. Then, the door latch is placed on the strike plate, creating an airtight seal when closed. If the strike plate is damaged, rusted or not installed correctly, it can stop the latch from locking the door securely.

The most common reason for an outdoor door lock to stick or not close is a misalignment of the latch and the strike plate. This can be confirmed using the "lipstick" test. Apply a little lipstick across the edge of the deadbolt and then cover it with masking tape. The lipstick will leave the mark when you close the door. This will reveal exactly where the latch connects to the strike plate. If the mark is too low or high, you can easily adjust the strike plate.

If your patio doors repair door locks for sliding aren't functioning properly they can help keep your home secure from intruders. It is imperative to resolve this issue as quickly as you can. By following these easy steps, you'll be able to fix your patio door's lock and restore its functionality in no time.