Car Key Button Repair

A broken car key button is frustrating. You might need to contact a 24-hour Locksmith Service or purchase an alternative remote.

You may be able save money by fixing your old key fob rather than replacing it. This is particularly true if the problem is caused by a worn switch or faulty contact.

Battery

If the buttons on your key fob do not respond when you pressing them, it could be a sign that the battery has died or is about to reach the end of life. It's easy to replace the battery yourself instead of paying an auto locksmith or dealership.

First look for the battery compartment. The battery compartment is typically located on the back of the key fob, and is often concealed behind a cover that slides out or an open button that opens the access point. When the compartment is exposed then look for the small button-cell battery. It's usually shaped like the shape of a coin and is marked with an plus and the minus symbol. Remove the old battery, and replace it with a brand new one. Check that the plus and symbol are aligned correctly.

Once the battery is in place, close the compartment and snap the two parts of the key fob. Before closing the door make sure to align and snap the pieces in place. To verify whether the buttons function properly, press any of them.

If your remote keyfob doesn't work after replacing the battery, there may be other problems that require a different type of repair. The fob's dropping in a puddle could cause it to stop functioning. It could also be a problem with the internal electrical system, or it may need to be deprogrammed. Try to figure out what's wrong with your key fob by using these other common automotive key repair troubleshooting methods.

Switches

There are a variety of switches found in the car key fob, depending on the year and make. The older style key is equipped with a chip that is visible inside the case. The modern keys function by transmitting signals to your car key repairs. The buttons on a key can be worn out or damaged by normal use, regardless of the type. They become hard to press or ineffective. If you press the button too hard it can cause further damage. It could also stop the key from functioning in the future.

If your key doesn't appear to be working, first try changing the battery. If this doesn't work, then you might need to clean your key's fob or re-adjust its switches. Since these tiny electronic switches spend a lot of time getting jostled around, they are more likely to fail than the larger components of your key fob repairs.

The switches are rubber-like, and they're coated with an electrically conducting film that can wear down over time. Luckily, they're also a very small part and affordable to replace. The old ones are soldered to the circuit board so you will need to carefully remove them without causing any damage to anything else. You can then solder the new ones in and then reassemble your fob.

An effective way to protect your car key fob from becoming damaged is to avoid using it for longer than a couple of hours at a time, and also to not leave it in places in areas where it is visible. Also, try to find a secure place to keep your key in when you aren't making use of it.

If the issue continues to persist after you have cleaned your key fob, replaced the battery and attempted to clean it, then you may need to talk to a locksmith. A professional can check the frequency of your key to see if it's still able to communicate with your vehicle, open and replace micro switches, swap cases and more.

Outer Case

A key fob spends a lot of time jostled around, and if the buttons aren't free to move between the case they can get stuck or even broken. If replacing the battery or cleaning it with a cotton swab and some rubbing alcohol doesn't fix the issue, then removing the case and inspecting may be necessary. If the contacts that the buttons touch are not a good fit, or if they are damaged, adjusting them could be the only solution.

Certain keys have buttons made of rubber, which wear out over time. The rubber expands, nails gouge into it, and the buttons become difficult to press. In this situation, the key may fail and it's time to replace the case or the buttons. This repair involves removing your remote, finding the button switches on the board, heating the solder, and carefully removing them. The circuit board then gets soldered with new buttons. The case can then be rebuilt with the horse shoe key blade piece attached. The new buttons should be tightly fitted inside the case to avoid them falling out.

Inner Case

Since your key fob is prone to be tossed around and sometimes be accidentally pressed and the buttons inside may get damaged or stuck over time. If your key fob ceases to function when you're away from home It is possible to solve the issue quickly using metallic tape and punch holes. This allows you to unlock doors, but not start the mobile car key repair near me. This simple fix will allow you to safely make it back to your vehicle and finish your trip.