How to Replace a Kia Sportage Replacement Key

For a variety of Kia models keys, the key has a keyless entry system built-in. The key is usually akin to an remote control, and is able to be replaced with a brand new one from an Kia dealer or locksmith.

Key fobs may stop working due to a number of reasons, such as batteries that are dead, worn-out buttons, signal interference or water damage. Here are some guidelines on how much is a replacement key For a Kia soul to get your kia smart key programming Sportage replacement key working again.

How do you replace the remote key or smartkey

The battery inside your Kia's smart key will eventually have to be replaced, regardless of whether it's a remote key that starts with a push button or a normal metal key that does not contain an electronic transponder. This is especially when the vehicle displays a message that indicates that the smart key or remote has a low battery.

Luckily, this is an easy procedure. To replace the keyfob battery remove your mechanical key from the slit at the back of the fob. Then, you need to pry the cover open. A small screw is found inside the key fob to hold the battery in its place. With a small screwdriver, take the screw off and remove the battery that was in place. Install the new battery and close the gap on the key fob.

Test the key fob by pressing the lock/unlock buttons. If the doors lock and unlock exactly as you expect, then you're set! You can now make use of Kia's hands-free lock/unlock function when your fingers start to get cold or you need to go on errands around Brandon.

Note: Certain key fobs (transponder chip or smart keys) might require their programming done. This requires a particular programming machine that only the dealer or automotive locksmith has access to. Other keys (non transponder keys made of steel) do not require programming. If your key requires to be reprogrammed, you must be aware of the key code number printed on the key code tag and keep it in a safe place.

How do I replace the battery?

If the Kia key fob does not respond to pressing the lock or unlock button, it is likely that the battery is low. A low battery may also cause other problems like the check engine light flashing on or a delay in cranking the engine. Fortunately, replacing the battery on the key fob is a fairly simple DIY task that requires only a few tools.

Be sure to turn off your vehicle and shut the doors before you begin. Find the small metal or a plastic piece on the bottom of the key fob. Jiggle it until the key pops out. You can then insert the key into the handle on the door of your driver to unlock your car.

To replace the key fob battery, remove the rear cover and use a plastic bar tool to loosen the latch holding the black negative battery cable. Remove the old battery and orient the new one so that the "+" positive side faces you, and the "-" negative side is facing the fob's metal electrical contacts. Push the new CR2032 battery straight into position with care to avoid using too much force to avoid damaging or bending the contacts of the metal.

Once the new battery is installed, turn the key fob off and back on in the ignition until the door locks. Then, you can test your kia remote key key fob and see whether it's functioning properly again.

How to replace the smart key?

You can have an ordinary keyfob or Smart Key based upon the model of Kia Sportage. The difference is that the smart key has tiny mechanical key blade in it, whereas the standard key fob does not. Both kinds of key fobs come with a battery inside them which eventually needs to be replaced. Fortunately, it's quite simple and takes just two minutes.

Before you start it is essential to make sure that you are on a flat surface with sufficient lighting and that your kia key copy is turned off. Also, keep in mind that there are tiny parts inside the fob that can be snagged if not cautious.

The first step is to locate the small release button that is located on the lower backside of your fob. It will be a circular button or a rectangular slot. You can open the key fob by pressing the button.

Once the key fob is open, remove the old battery. The new battery is a CR-2032 that can be purchased online or at a local auto parts store. Once you're done, your key fob should permit you to lock the vehicle, unlock it, and then start your vehicle even if it's not running.

How to replace a mechanical key

The Kia keyfob is an excellent convenience that allows us to lock or unlock our car simply by pressing one button. Like any other device that is used, the Kia key fob can occasionally have problems. Luckily, there are steps that can be taken to fix these issues and ensure that our key fobs are in good working order over the long haul.

A dead or weak battery is one of the most common problems. This could cause the fob to stop working altogether or work intermittently. If this is the case, replace the battery with a new one.

If this doesn't resolve the problem, try using a standard flathead screwdriver to open the casing of the fob's plastic. Be sure not to damage any internal components, or scratch the plastic. After opening, carefully remove the battery that was removed and replace it with a brand new one.

Close and open the door using the mechanical key. (Every kia keys made fob comes with an emergency mechanical key that fits into the slot). Test the key fob to confirm it's functioning correctly. Contact a dealer, or a locksmith to resolve the problem if the fob is still not working. Make sure they make you an emergency key that functions for all trunk and door cylinders to avoid lockouts again.